The P2794 fault code in automobiles indicates a problem with the transmission range sensor or shifter circuit.
The most common symptom is the illumination of the engine light or service engine soon warning light. The cause of this fault code could be a defective range sensor, faulty transmission shifter, or poor electrical connection in the transmission shifter circuit. The repair importance is high as it affects the transmission’s performance.
The repair difficulty is moderate, and the repair time is estimated at 1.0 hour.
To fix the issue, one should visually inspect the wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
P2794: Unresponsive Acceleration – Symptoms & Solutions
If you notice the Engine Light ON (or Service Engine Soon Warning Light), it could be due to the p2794 fault code. Here are the symptoms to look out for:
- The P2794 fault code in automobiles can cause several symptoms, including the engine light turning on or the service engine soon warning light appearing.
- Other symptoms may include issues with shifting gears, transmission slippage, and decreased fuel efficiency.
- Additionally, the vehicle may experience difficulty accelerating or may stall while driving.
- It is important to address these symptoms promptly to prevent further damage to the vehicle.
P2794: Uncovering The Culprits Behind The Fault Code
The automobile fault code P2794 can be caused by a range of issues, including a defective range sensor and faulty transmission shifter.
- The automobile fault code P2794 can be caused by a defective range sensor.
- It can also be caused by a faulty transmission shifter.
- Another cause of this fault code is an open or shorted transmission shifter harness.
- Additionally, a poor electrical connection in the transmission shifter circuit can also trigger this fault code.
Fix Code P2794: Simple Steps To Get Your Car Running
Below are some possible fixes for the automobile fault code p2794, including inspecting wiring harness and connectors for damage or corrosion.
- To fix the automobile fault code P2794, you need to check the possible causes listed above.
- Visually inspect the related wiring harness and connectors for any damage.
- Look for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
P2794: Affordable Fix For Your Car’s Transmission
The automobile fault code P2794 can be diagnosed and fixed within an estimated repair time of 1.0 hour.
The cost of repair is influenced by the repair time, which is commonly charged between $75 and $150 per hour by most auto repair shops.
Therefore, the total cost of fixing the P2794 fault code will depend on the hourly rate charged by the repair shop and the estimated repair time required to fix the issue.
P2794: Transmission Input Shaft Speed Sensor Circuit Intermittent
The P2794 code is related to the Gear Shift Direction Circuit signal. The Transmission Control Module (TCM) is responsible for monitoring this signal. If the signal is not within the factory specifications, the TCM will set the OBDII code.
The P2794 code specifically indicates that the Gear Shift Direction Circuit signal is low. This fault code can cause issues with the transmission and may result in difficulty shifting gears.
It is important to address this issue promptly to avoid further damage to the transmission.
FAQ
If your engine light is on and you’re getting the P2794 fault code, it could be due to a defective range sensor, faulty transmission shifter, or poor electrical connection in the transmission shifter circuit. To fix this issue, you should visually inspect the wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
If you’re experiencing the P2794 fault code, which can cause the engine light to turn on, you may need to visually inspect the related wiring harness and connectors. This fault code can be caused by a defective range sensor, faulty transmission shifter, or poor electrical connection in the transmission shifter circuit. To fix the issue, check the possible causes listed above and inspect the wiring harness and connectors for any damage or corrosion. Look for broken, bent, pushed out, or corroded connector pins.
If you’re experiencing the P2794 fault code, start by checking the possible causes, which include a defective range sensor, faulty transmission shifter, open or shorted transmission shifter harness, or poor electrical connection in the transmission shifter circuit. Visually inspect the related wiring harness and connectors, and look for damaged components and broken, bent, pushed out, or corroded connector’s pins.
Wrap Up
If your engine light is on and you have a P2794 code, it could be due to a defective range sensor, faulty transmission shifter, or poor electrical connection.
Check the wiring harness and connectors for damage and inspect the components for any issues.
