The P2792 fault code in automobiles indicates a problem with the transmission range sensor or shifter circuit. The most common symptom is the illumination of the engine light or service engine soon warning light.
The cause of this fault code could be a defective range sensor, faulty transmission shifter, or poor electrical connection in the transmission shifter circuit. The repair importance is high as it affects the transmission’s performance and can lead to further damage if not addressed promptly.
The repair difficulty is moderate, and the fix involves visually inspecting the wiring harness and connectors for damage and checking for broken or corroded connector pins. The repair time is estimated to be around 1.0 hour.
It is essential to interpret the fault code correctly to identify the root cause of the problem and avoid unnecessary repairs.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
P2792: Identifying Transmission Slippage Symptoms
If you notice the Engine Light ON (or Service Engine Soon Warning Light), it could be due to the p2792 fault code. Here are the symptoms to look out for:
- The P2792 fault code in an automobile can cause several symptoms, including the engine light turning on or the service engine soon warning light appearing.
- Other symptoms may include issues with shifting gears, transmission slippage, and decreased fuel efficiency.
- Additionally, the vehicle may experience a decrease in power or acceleration, and the transmission may fail to engage or disengage properly.
- It is important to address these symptoms promptly to prevent further damage to the vehicle.
P2792: Uncovering The Culprits Behind The Fault Code
The automobile fault code P2792 can be caused by a range of issues, including a defective range sensor and faulty transmission shifter.
- The automobile fault code P2792 can be caused by a defective range sensor.
- It can also be caused by a faulty transmission shifter.
- Another cause of this fault code is an open or shorted transmission shifter harness.
- Additionally, a poor electrical connection in the transmission shifter circuit can also trigger this fault code.
Fix Code P2792: Simple Steps To Get Your Car Running
Below are the possible fixes for the automobile fault code: p2792, including inspecting wiring harness, connectors, and damaged components.
- To fix the automobile fault code P2792, first, check the possible causes listed above.
- Then, visually inspect the related wiring harness and connectors.
- Look for any damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
P2792: Affordable Fix For Complex Auto Issue
The automobile fault code P2792 can be diagnosed and fixed within an estimated repair time of 1.0 hour.
The cost of repair is influenced by the repair time, which is commonly charged between $75 and $150 per hour by most auto repair shops. Therefore, the total cost of fixing the P2792 fault code will depend on the hourly rate charged by the repair shop and the estimated repair time required to fix the issue.
P2792: Transmission Fluid Pump Control Circuit Low – Explained
The P2792 code is related to the Gate Select Direction Circuit signal.
The Transmission Control Module (TCM) is responsible for monitoring this signal.
If the signal is not within the factory specifications, the TCM will set the OBDII code. The P2792 code specifically indicates that the Gate Select Direction Circuit signal is high. This fault code can cause issues with the transmission and should be addressed promptly.
A professional mechanic can diagnose and repair the issue to ensure proper functioning of the vehicle.
FAQ
If your engine light is on and you’re getting the P2792 fault code, it could be due to a defective range sensor, faulty transmission shifter, or poor electrical connection in the transmission shifter circuit. To fix this issue, you should visually inspect the wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
If you’re experiencing the P2792 fault code, which can be caused by a defective range sensor, faulty transmission shifter, or poor electrical connection in the transmission shifter circuit, you can visually inspect the related wiring harness and connectors to fix the issue. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. It’s important to check the “Possible Causes” listed above before proceeding with any repairs.
If you’re experiencing the P2792 fault code, start by checking the possible causes, which include a defective range sensor, faulty transmission shifter, open or shorted transmission shifter harness, or poor electrical connection in the transmission shifter circuit. Visually inspect the related wiring harness and connectors, and look for damaged components and broken, bent, pushed out, or corroded connector’s pins.
Wrap Up
If your engine light is on, it could be due to a defective range sensor, faulty transmission shifter, or poor electrical connection. Check the wiring harness and connectors for damage, broken or corroded pins.
Inspect the components listed above to fix the issue.
