[SOLVED] P2791 Code: Fixing Gate Select Direction Circuit Low

The P2791 fault code in automobiles indicates a problem with the transmission range sensor circuit. This can result in the engine light turning on or a service engine soon warning light.

The cause of this issue can be a defective range sensor, faulty transmission shifter, or poor electrical connection in the transmission shifter circuit. It is important to visually inspect the wiring harness and connectors for any damage or corrosion.

The repair time for this issue is estimated to be around 1.0.

To interpret the fault code, it is recommended to check the possible causes listed above and look for any broken or bent components.

Repair Importance Level10.0 (Out of 10)
Estimated Repair TimeApproximately 1.0 hour
Repair Difficulty Level10.0 (Out of 10)

If you notice the Engine Light ON (or Service Engine Soon Warning Light), it could be due to the p2791 fault code. Here are the symptoms to look out for:

  • The P2791 fault code in automobiles can cause several symptoms, including the engine light turning on or the service engine soon warning light appearing.
  • Other symptoms may include transmission shifting issues, decreased fuel efficiency, and engine stalling or hesitation.
  • Additionally, the vehicle may experience difficulty starting or accelerating, and there may be unusual noises or vibrations coming from the engine or transmission.
  • It is important to address these symptoms promptly to prevent further damage to the vehicle and ensure safe driving conditions.

The automobile fault code P2791 can be caused by a range of issues, including a defective range sensor and faulty transmission shifter.

  • The automobile fault code P2791 can be caused by a defective range sensor.
  • It can also be caused by a faulty transmission shifter.
  • Another cause of this fault code is an open or shorted transmission shifter harness.
  • Additionally, a poor electrical connection in the transmission shifter circuit can also trigger this fault code.

To fix the automobile fault code p2791, check the possible causes and inspect the related wiring harness and connectors for any damage.

  • To fix the automobile fault code P2791, you need to check the possible causes listed above.
  • Visually inspect the related wiring harness and connectors for any damage.
  • Look for broken, bent, pushed out, or corroded connector’s pins.
  • This fix will take an estimated repair time of 1.0 hour.

The fault code P2791 indicates a problem with the clutch actuator circuit.

The estimated repair time for this issue is 1.0 hour. The cost of fixing this issue can vary depending on the auto repair shop, but it is common for them to charge between $75 and $150 per hour.

These factors should be considered when diagnosing and fixing the P2791 fault code.

The P2791 code is related to the Gate Select Direction Circuit signal. The Transmission Control Module (TCM) is responsible for monitoring this signal.

If the signal is not within the factory specifications, the TCM will set the P2791 code. This code specifically indicates that the Gate Select Direction Circuit signal is low. It is important to address this issue promptly to ensure proper functioning of the transmission system.

What are the possible causes of the P2791 automobile fault code?

If you see the engine light on or the service engine soon warning light, it could be due to the P2791 fault code. This code is caused by a defective range sensor, faulty transmission shifter, open or shorted transmission shifter harness, or poor electrical connection in the transmission shifter circuit. To fix this issue, you should check the possible causes listed above, visually inspect the related wiring harness and connectors, and look for damaged components or broken, bent, pushed out, or corroded connector’s pins.

How can one visually inspect the related wiring harness and connectors to fix the P2791 fault code?

If you’re experiencing the P2791 fault code, which can be caused by a defective range sensor, faulty transmission shifter, or poor electrical connection in the transmission shifter circuit, you can visually inspect the related wiring harness and connectors to fix the issue. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. It’s important to check the “Possible Causes” listed above before proceeding with any repairs.

What are the signs that the Transmission Shifter harness is open or shorted, causing the P2791 fault code?

If you notice the engine light or service engine soon warning light is on, it could be a sign of a P2791 fault code caused by an open or shorted Transmission Shifter harness. This issue can also be caused by a defective Range Sensor, faulty Transmission Shifter, or poor electrical connection in the Transmission Shifter circuit. To fix this problem, you should visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.

p2791 error fault code explained

If your engine light is on, it could be due to a defective range sensor, faulty transmission shifter, or poor electrical connection. Check the wiring harness and connectors for damage, broken or corroded pins. Inspect the components listed above to fix the issue.

Scroll to Top