[SOLVED] P2790 Code: Fixing Gate Select Direction Circuit Issues

The P2790 fault code in automobiles refers to a problem with the transmission range sensor circuit. The most common symptom is the illumination of the engine light or service engine soon warning light.

The cause of this issue could be a defective range sensor, faulty transmission shifter, or poor electrical connection in the transmission shifter circuit. The importance of repairing this issue lies in the fact that it can affect the performance of the transmission and lead to further damage. The repair difficulty is moderate, and it takes around 1.0 hour to fix.

To interpret the fault code, one needs to check the possible causes listed above and visually inspect the related wiring harness and connectors.

Repair Importance Level10.0 (Out of 10)
Estimated Repair TimeApproximately 1.0 hour
Repair Difficulty Level10.0 (Out of 10)

If you notice the Engine Light ON or Service Engine Soon Warning Light, it could be a sign of p2790 fault code.

Here are the symptoms to look out for:

  • The P2790 fault code in an automobile can cause several symptoms, including the engine light turning on or the service engine soon warning light appearing.
  • Other symptoms may include issues with shifting gears, transmission slippage, and decreased fuel efficiency.
  • Additionally, the vehicle may experience difficulty accelerating or may stall while driving.
  • It is important to address these symptoms promptly to prevent further damage to the vehicle.

The automobile fault code P2790 can be caused by a range of issues, including a defective range sensor and faulty transmission shifter.

  • The automobile fault code P2790 can be caused by a defective range sensor.
  • It can also be caused by a faulty transmission shifter.
  • Another cause of this fault code is an open or shorted transmission shifter harness.
  • Additionally, a poor electrical connection in the transmission shifter circuit can also trigger this fault code.

Below are some possible fixes for the automobile fault code p2790, including inspecting wiring harness and connectors for damage or corrosion.

  • To fix the automobile fault code P2790, you need to check the possible causes listed above.
  • Visually inspect the related wiring harness and connectors for any damage.
  • Look for broken, bent, pushed out, or corroded connector’s pins.
  • This fix will take an estimated repair time of 1.0 hour.

The fault code P2790 indicates a problem with the clutch actuator circuit. The estimated repair time for this issue is 1.0 hour.

The cost of fixing this issue can vary depending on the auto repair shop, but it is common for them to charge between $75 and $150 per hour.

Therefore, the total cost of fixing the P2790 fault code can range from $75 to $150.

The P2790 code is related to the Gate Select Direction Circuit signal. The Transmission Control Module (TCM) is responsible for monitoring this signal. If the signal is not within the factory specifications, the TCM will set the P2790 code.

This fault code indicates that there is an issue with the Gate Select Direction Circuit signal.

It is important to address this issue promptly to avoid further damage to the vehicle.

What are the possible causes of the P2790 automobile fault code?

If you see the engine light on or the service engine soon warning light, it could be due to the P2790 fault code. This code is caused by a defective range sensor, faulty transmission shifter, open or shorted transmission shifter harness, or poor electrical connection in the transmission shifter circuit. To fix this issue, you should check the possible causes listed above, visually inspect the related wiring harness and connectors, and look for damaged components or broken, bent, pushed out, or corroded connector’s pins.

How can I fix the P2790 automobile fault code?

If you’re experiencing the P2790 fault code, which is indicated by the engine light or service engine soon warning light turning on, it could be due to a defective range sensor, faulty transmission shifter, or poor electrical connection in the transmission shifter circuit. To fix this issue, you should visually inspect the wiring harness and connectors, checking for any damaged components or broken, bent, pushed out, or corroded connector pins.

What should I visually inspect to troubleshoot the P2790 automobile fault code?

If you’re troubleshooting the P2790 automobile fault code, start by checking for an illuminated engine light or service engine soon warning light. The cause of this issue could be a defective range sensor, faulty transmission shifter, open or shorted transmission shifter harness, or poor electrical connection in the transmission shifter circuit. To fix the problem, visually inspect the related wiring harness and connectors, checking for damaged components and broken, bent, pushed out, or corroded connector pins.

p2790 error fault code explained

If your engine light is on, it could be due to a defective range sensor, faulty transmission shifter, or poor electrical connection. Check the wiring harness and connectors for damage, broken or corroded pins. Visually inspect the components and connectors.

Scroll to Top