[SOLVED] P2758 Code: Fixing Stuck Torque Converter Clutch Pressure Control Solenoid

If you’re experiencing an illuminated Engine Light or Service Engine Soon Warning Light, it could be due to the P2758 fault code. This code indicates a problem with the Torque Converter Clutch Pressure Control Solenoid, which can be caused by a faulty solenoid, an open or shorted harness, or a poor electrical connection.

The importance of repairing this issue lies in the fact that it can lead to decreased fuel efficiency and potential damage to the transmission.

While the repair time is estimated at 1.0, it’s important to visually inspect the wiring harness and connectors for any damage or corrosion.

To interpret the fault code, it’s recommended to check the “Possible Causes” listed above.

Repair Importance Level10.0 (Out of 10)
Estimated Repair TimeApproximately 1.0 hour
Repair Difficulty Level10.0 (Out of 10)

If you notice the Engine Light ON or Service Engine Soon Warning Light, it could be a sign of p2758 fault code. Here are the symptoms to look out for:

  • The P2758 fault code in an automobile can cause several symptoms.
  • The most common symptom is the illumination of the engine light or service engine soon warning light.
  • Other symptoms include harsh shifting, transmission slippage, decreased fuel efficiency, and decreased engine performance.
  • Additionally, the vehicle may experience difficulty starting or may stall while driving.
  • It is important to address these symptoms promptly to prevent further damage to the vehicle.

P2758 fault code can be caused by a faulty solenoid, openshorted harness, or poor electrical connection.

  • The automobile fault code P2758 can be caused by a faulty Torque Converter Clutch Pressure Control Solenoid.
  • It can also be caused by an open or shorted Torque Converter Clutch Pressure Control Solenoid harness.
  • Additionally, a poor electrical connection in the Torque Converter Clutch Pressure Control Solenoid circuit can also trigger this fault code.

To fix the automobile fault code p2758, check the possible causes and inspect the related wiring harness and connectors for any damage or corrosion.

  • To fix the automobile fault code P2758, first, check the possible causes listed above.
  • Then, visually inspect the related wiring harness and connectors.
  • Look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
  • This fix will take an estimated repair time of 1.0 hour.

The automobile fault code P2758 can be diagnosed and fixed within an estimated repair time of 1.0 hour. The cost of repair is influenced by the repair time, which is commonly charged between $75 and $150 per hour by most auto repair shops. Therefore, the total cost of fixing the P2758 fault code will depend on the hourly rate charged by the repair shop and the estimated repair time required to fix the issue.

The P2758 code is an OBDII fault code that indicates an issue with the Torque Converter Clutch Pressure Control Solenoid circuit signal. The Engine Control Module (ECM) monitors this signal and sets the code when the solenoid is not within factory specifications.

The code specifically refers to the Torque Converter Clutch Pressure Control Solenoid Control Circuit being stuck in the “Off” position. This can cause issues with the vehicle’s transmission and should be addressed promptly.

What are the possible causes of the P2758 automobile fault code?

The P2758 fault code in an automobile is indicated by the engine light turning on. The possible causes of this fault code include a faulty torque converter clutch pressure control solenoid, an open or shorted solenoid harness, or a poor electrical connection in the solenoid circuit. To fix this issue, one should visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.

How can I visually inspect the related wiring harness and connectors to fix the P2758 fault code?

If you’re experiencing the P2758 fault code, which is indicated by the engine light being on or the service engine soon warning light, there are a few things you can do to fix it. The cause of this issue could be a faulty torque converter clutch pressure control solenoid, an open or shorted solenoid harness, or a poor electrical connection in the solenoid circuit. To address these issues, you should visually inspect the related wiring harness and connectors. Look for any damaged components and check for broken, bent, pushed out, or corroded connector pins.

What are the symptoms of the P2758 automobile fault code and how can I identify them?

The P2758 fault code is indicated by the Engine Light ON or Service Engine Soon Warning Light. It is caused by a faulty Torque Converter Clutch Pressure Control Solenoid, an open or shorted harness, or poor electrical connection. To fix it, inspect the wiring harness and connectors for damage, broken, bent, pushed out, or corroded pins.

p2758 error fault code explained

If you see the Engine Light ON or Service Engine Soon Warning Light, it could be due to a faulty Torque Converter Clutch Pressure Control Solenoid, an open or shorted harness, or poor electrical connection.

To fix it, visually inspect the wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.

Scroll to Top