[SOLVED] P267C Code: Low Circuit Solution For Bank 2 Rocker Arm Actuator

The P267C fault code in automobiles refers to a problem with the ‘B’ Rocker Arm Actuator Sensor. The most common symptom of this issue is the Engine Light turning on.

The cause of this problem could be low or overfilled engine oil, incorrect engine oil type, faulty sensor, or poor electrical connection.

It is important to fix this issue as it can lead to engine damage. The repair time for this issue is around 1.0 hour. To fix this problem, one needs to visually inspect the wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.

Repair Importance Level10.0 (Out of 10)
Estimated Repair TimeApproximately 1.0 hour
Repair Difficulty Level10.0 (Out of 10)

If you see the Engine Light ON or Service Engine Soon Warning Light, it could be due to the p267c fault code.

Here are the symptoms to look out for:

  • The P267C fault code in an automobile can cause several symptoms, including the engine light turning on or the service engine soon warning light appearing.
  • Other symptoms may include reduced engine power, poor acceleration, rough idling, stalling, and decreased fuel efficiency.
  • Additionally, the vehicle may experience transmission shifting issues, such as delayed or harsh shifting.
  • It is important to address these symptoms promptly to prevent further damage to the vehicle and ensure safe driving conditions.

The P267C automobile fault code can be caused by various factors, including low or overfilled engine oil, incorrect oil type, and faulty sensors.

  • The automobile fault code P267C can be caused by low or overfilled engine oil.
  • It can also be caused by using the incorrect engine oil type.
  • Another possible cause is a faulty ‘B’ Rocker Arm Actuator Sensor.
  • The ‘B’ Rocker Arm Actuator Sensor harness being open or shorted can also trigger this fault code.
  • Lastly, a poor electrical connection in the ‘B’ Rocker Arm Actuator Sensor circuit can cause the P267C fault code to appear.

To fix the automobile fault code p267c, check the possible causes and inspect related wiring harness and connectors for damage.

  • To fix the automobile fault code p267c, first, check the possible causes listed above.
  • Then, visually inspect the related wiring harness and connectors.
  • Look for any damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
  • This fix will take an estimated repair time of 1.0 hour.

The automobile fault code P267C can be diagnosed and fixed within an estimated repair time of 1.0 hour.

The cost of repair is influenced by the repair time, which is commonly charged between $75 and $150 per hour by most auto repair shops. Therefore, the total cost of diagnosis and fixing the P267C fault code will depend on the hourly rate charged by the repair shop and the estimated repair time required to fix the issue.

The P267C code is related to the engine’s variable valve timing system.

The Engine Control Module (ECM) commands the Rocker Arm Actuator to control the oil hydraulic circuit.

The ‘B’ Rocker Arm Actuator Position Sensor signal is monitored by the ECM. If the signal is out of factory specifications, the ECM sets the OBDII and triggers the P267C code.

This code indicates that there is a problem with the ‘B’ Rocker Arm Actuator Position Sensor Circuit Low Bank.

What are the possible causes of the P267C fault code?

If you’re experiencing the P267C fault code, your engine light may be on. This could be due to low or overfilled engine oil, incorrect engine oil type, a faulty ‘B’ Rocker Arm Actuator Sensor, or a poor electrical connection in the ‘B’ Rocker Arm Actuator Sensor circuit. To fix the issue, check the possible causes listed above, visually inspect the related wiring harness and connectors, and look for damaged components or corroded connector pins.

How can I visually inspect the wiring harness and connectors related to the P267C fault code?

If you’re experiencing the P267C fault code, which can cause the engine light to turn on, you should visually inspect the wiring harness and connectors related to the issue. This fault code can be caused by low or overfilled engine oil, incorrect engine oil type, a faulty ‘B’ Rocker Arm Actuator Sensor, an open or shorted ‘B’ Rocker Arm Actuator Sensor harness, or a poor electrical connection in the circuit. To fix the issue, check the possible causes listed above and inspect the wiring harness and connectors for any damage or corrosion. Look for broken, bent, pushed out, or corroded connector pins.

What should I do if I find damaged components or broken, bent, pushed out, or corroded connector’s pins while inspecting the P267C fault code?

If you find damaged components or broken, bent, pushed out, or corroded connector’s pins while inspecting the P267C fault code, you should visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. It is important to check the “Possible Causes” listed above to determine the root cause of the issue.

p267c error fault code explained

If your engine light is on, it could be due to low or overfilled engine oil, incorrect oil type, or a faulty ‘B’ Rocker Arm Actuator Sensor. Check the possible causes listed above, visually inspect the wiring harness and connectors, and look for damaged components or corroded pins.

Scroll to Top