The P2673 fault code in automobiles indicates a problem with the injection pump. The most common symptom is the illumination of the engine light or service engine soon warning light. The cause of this fault code could be a faulty injection pump, an open or shorted injection pump harness, or a poor electrical connection in the injection pump circuit.
It is important to address this issue promptly as it can lead to reduced engine performance and fuel efficiency. The repair process involves visually inspecting the wiring harness and connectors, checking for damaged components, and looking for broken, bent, pushed out, or corroded connector pins.
The repair time for this fault code is estimated to be around 1.0 hour.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
P2673: Unresponsive Acceleration – Symptoms & Solutions
If you notice the Engine Light ON (or Service Engine Soon Warning Light), it could be due to the p2673 fault code. Here are the symptoms to look out for:
- The P2673 fault code in automobiles can cause several symptoms, including the engine light turning on or the service engine soon warning light appearing.
- Other symptoms may include a decrease in engine power, poor acceleration, rough idling, stalling, and difficulty starting the engine.
- Additionally, the vehicle may experience transmission shifting issues, decreased fuel efficiency, and increased emissions.
- It is important to address these symptoms promptly to prevent further damage to the vehicle and ensure safe driving conditions.
Decoding P2673: Common Causes Of The Fault Code
The automobile fault code P2673 can be caused by a faulty injection pump, open or shorted injection pump harness, or poor electrical connection in the injection pump circuit.
- The automobile fault code P2673 can be caused by a faulty injection pump.
- It can also be caused by an open or shorted injection pump harness.
- Additionally, a poor electrical connection in the injection pump circuit can also trigger this fault code.
Fix Code P2673: Simple Steps To Get Your Car Running
To fix the automobile fault code p2673, check the possible causes and inspect related components for damage or corrosion.
- To fix the automobile fault code P2673, you need to check the possible causes listed above.
- Visually inspect the related wiring harness and connectors for any damage.
- Look for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
P2673: Affordable Fix For Complex Auto Fault Code
The automobile fault code P2673 can be diagnosed and fixed within an estimated repair time of 1.0 hour. The cost of repair is influenced by the hourly rate charged by the auto repair shop, which typically ranges between $75 and $150 per hour.
Therefore, the total cost of fixing the P2673 fault code will depend on the hourly rate charged by the auto repair shop and the estimated repair time required to fix the issue.
P2673: Your Engine’s Power Is At Risk – Here’s Why
The P2673 code is related to the Injection Pump Timing Calibration.
The Powertrain Control Module (PCM) is responsible for monitoring the Injection Pump Timing. If the Injection Pump Timing is not within the factory specifications, the PCM will set the P2673 code. This code indicates that the Injection Pump Timing Calibration is not correct.
It is important to address this issue promptly to avoid further damage to the vehicle.
FAQ
If you see the engine light on or the service engine soon warning light, it could be due to the P2673 fault code. This code is caused by a faulty injection pump, an open or shorted injection pump harness, or a poor electrical connection in the injection pump circuit. To fix this issue, you should visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
If you’re experiencing the P2673 fault code, start by checking the “Possible Causes” listed above. To visually inspect the related wiring harness and connectors, look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins. This will help you identify any issues with the Injection Pump harness, which could be causing the problem.
Ignoring the P2673 fault code, which indicates a faulty injection pump or poor electrical connection, can lead to serious consequences. The engine light will remain on, and the vehicle may experience reduced performance, decreased fuel efficiency, and potential engine damage. It is crucial to address the issue promptly by visually inspecting the wiring harness and connectors and checking for damaged components to avoid further complications.
Wrap Up
If your engine light is on, it could be due to a faulty injection pump, open or shorted injection pump harness, or poor electrical connection. Visually inspect the wiring harness and connectors for damage and check for broken, bent, pushed out, or corroded connector pins.
