The P1B92 automobile fault code indicates a problem with the HybridElectric Vehicle Battery Pack or the Battery Interface Control Module.
The most common symptom is the Engine Light turning on. The cause of this issue is a faulty battery pack or control module.
It is important to address this issue promptly as it can lead to reduced fuel efficiency and performance.
The repair difficulty is moderate, and it takes approximately 1.0 hour to fix.
To diagnose the problem, one should visually inspect the wiring harness and connectors for any damage or corrosion.
The possible fix is to replace the faulty components.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
P1B92: Uncovering The Symptoms Of This Auto Fault Code
If you notice the Engine Light ON or Service Engine Soon Warning Light, it could be a sign of p1b92 fault code. Here are the symptoms to look out for:
- The P1B92 fault code in an automobile can cause several symptoms, including the engine light turning on or the service engine soon warning light appearing.
- Other symptoms may include reduced engine power, decreased fuel efficiency, and difficulty starting the engine.
- Additionally, the vehicle may experience rough idling or stalling, and there may be a noticeable decrease in acceleration.
- It is important to address these symptoms promptly to prevent further damage to the vehicle and ensure safe driving conditions.
Decoding P1B92: Common Causes Of The Fault Code
P1B92 fault code can be caused by a faulty battery pack or battery interface control module in hybridelectric vehicles.
- The automobile fault code P1B92 can be caused by a faulty Hybrid/Electric Vehicle Battery Pack.
- It can also be caused by a faulty Hybrid/Electric Vehicle Battery Interface Control Module.
- These are the only two causes of the P1B92 fault code.
Fix Code P1B92: Simple Steps To Get Your Car Running
Below are the possible fixes for the automobile fault code p1b92, including inspecting wiring harness and connectors for damage or corrosion.
- To fix the automobile fault code p1b92, first, check the possible causes listed above.
- Then, visually inspect the related wiring harness and connectors.
- Look for any damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
Crunching The Numbers: P1B92 Repair Cost & Complexity
The factors that influence the cost of diagnosing and fixing the automobile fault code P1B92 are: – The estimated repair time is 1.0 hour. – Auto repair shops typically charge between $75 and $150 per hour. – The cost may vary depending on the location and reputation of the repair shop. – The cost may also depend on the severity of the issue and the parts that need to be replaced. – It is important to get a detailed estimate from the repair shop before proceeding with the repairs.
P1B92: Your Car’s Battery Needs Attention
The P1B92 code is related to the HybridElectric Vehicle battery pack. The battery pack contains 288 cells grouped in parallel and connected in-series.
The battery energy control module monitors the voltage of the 96 battery cell groups through the four hybridEV battery interface control modules. The battery energy control module will determine when a fault condition is present and communicate it to the hybridEV powertrain control module 2 through serial data.
The P1B92 code indicates a high voltage in the HybridElectric Vehicle Battery 58 Circuit. The hybridEV powertrain control module 2 is the host controller for diagnostic trouble code information.
FAQ
If you see the engine light on or the service engine soon warning light, it could be due to the P1B92 fault code. This code is usually caused by a faulty hybrid/electric vehicle battery pack or a faulty hybrid/electric vehicle battery interface control module. To fix this issue, you should visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
If you’re experiencing the P1B92 fault code, which is indicated by the Engine Light ON or Service Engine Soon Warning Light, you may have a faulty Hybrid/Electric Vehicle Battery Pack or a faulty Hybrid/Electric Vehicle Battery Interface Control Module. To fix this issue, you should check the possible causes listed above and visually inspect the related wiring harness and connectors. Look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
If you’re fixing the P1B92 fault code, keep an eye out for the engine light or service engine soon warning light turning on. This is a symptom of the issue. The cause could be a faulty hybrid/electric vehicle battery pack or a faulty hybrid/electric vehicle battery interface control module. To fix it, check the possible causes listed above and visually inspect the related wiring harness and connectors. Look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
Wrap Up
If your engine light is on, it could be due to a faulty hybridelectric vehicle battery pack or interface control module.
Check the wiring harness and connectors for damage, broken or corroded pins. Inspect the components listed above to fix the issue.
