The P1A60 automobile fault code indicates a problem with the Hybrid Powertrain Control Module 2, which can cause the engine light to turn on. The cause of this issue could be a faulty module, an open or shorted harness, or a poor electrical connection. It is important to visually inspect the wiring harness and connectors for any damage or corrosion.
The repair time for this issue is estimated to be around 1.0. To interpret the fault code, it is recommended to check the “Possible Causes” listed above and look for any broken or bent connector pins.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
P1A60: Uncovering The Symptoms Of This Auto Fault Code
If you notice the Engine Light ON or Service Engine Soon Warning Light, it could be a sign of p1a60 fault code. Here are the symptoms to look out for:
- The P1A60 fault code in automobiles can cause several symptoms, including the engine light turning on or the service engine soon warning light appearing.
- Other symptoms may include reduced engine power, decreased fuel efficiency, and difficulty starting the engine.
- Additionally, the vehicle may experience stalling or hesitation during acceleration, and the battery may fail to charge properly.
- It is important to address these symptoms promptly to prevent further damage to the vehicle.
Decoding P1A60: Common Causes Of This Fault Code
The P1A60 fault code in automobiles can be caused by various factors, including a faulty Hybrid Powertrain Control Module 2, open or shorted harness, and poor electrical connection in the circuit.
- The automobile fault code P1A60 can be caused by a faulty Hybrid Powertrain Control Module 2.
- It can also be caused by an open or shorted Hybrid Powertrain Control Module 2 harness.
- Additionally, a poor electrical connection in the Hybrid Powertrain Control Module 2 circuit can also trigger this fault code.
Fix Code P1A60: Simple Steps To Get Your Car Running
Below are the possible fixes for the automobile fault code p1a60, including inspecting wiring harness and connectors for damage or corrosion.
- To fix the automobile fault code p1a60, you need to check the possible causes listed above.
- Visually inspect the related wiring harness and connectors.
- Look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
P1A60: Affordable Fix For Complex Hybrid Fault
The automobile fault code P1A60 can be diagnosed and fixed within an estimated repair time of 1.0 hour. The cost of repair is influenced by the repair time, which is commonly charged between $75 and $150 per hour by most auto repair shops.
Therefore, the total cost of diagnosis and fixing the P1A60 fault code will depend on the hourly rate charged by the repair shop and the estimated repair time required to fix the issue.
P1A60: The Low Battery Charge Fault Code Explained
The P1A60 code is related to the Battery Energy Control Module Ignition Accessory Switch Circuit. This fault code is triggered when the Hybrid Powertrain Control Module 2 sends a serial data wake-up power mode status message to the Battery Energy Control Module.
The Hybrid Powertrain Control Module 2 also powers up the serial data wake-up circuit to the Battery Energy Control Module when the vehicle power mode is Vehicle ON or Vehicle in Service Mode. The P1A60 code indicates that there is a low voltage issue in the ignition accessory switch circuit of the Battery Energy Control Module.
This can cause problems with the vehicle’s power supply and should be addressed promptly.
FAQ
If you see the engine light on or the service engine soon warning light, it could be due to the P1A60 fault code. This code is caused by a faulty Hybrid Powertrain Control Module 2, an open or shorted Hybrid Powertrain Control Module 2 harness, or a poor electrical connection in the Hybrid Powertrain Control Module 2 circuit. To fix this issue, you should check the possible causes listed above, visually inspect the related wiring harness and connectors, and look for damaged components or broken, bent, pushed out, or corroded connector’s pins.
If you’re experiencing an Engine Light ON or Service Engine Soon Warning Light, it could be due to a faulty Hybrid Powertrain Control Module 2. To fix this issue, you should visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. This will help you identify if the Hybrid Powertrain Control Module 2 harness is open or shorted, or if there is a poor electrical connection in the circuit.
If you find damaged components or broken, bent, pushed out, or corroded connector’s pins during the inspection for the P1A60 fault code, it is important to address them immediately. These issues can cause poor electrical connections and may be the cause of the fault code. Visually inspect the related wiring harness and connectors to identify any issues. Once identified, replace or repair the damaged components and ensure that the connectors are properly connected. This will help to resolve the issue and prevent further damage to the Hybrid Powertrain Control Module 2.
Wrap Up
If you see the Engine Light ON or Service Engine Soon Warning Light, it could be due to a faulty Hybrid Powertrain Control Module 2, an open or shorted harness, or poor electrical connection.
Check the possible causes, inspect the wiring harness and connectors, and look for damaged components or corroded pins.
