The automobile fault code P1655 indicates a problem with the EVAP Purge Solenoid. The most common symptom is the Engine Light being ON or the Service Engine Soon Warning Light. The cause of this fault code can be a faulty EVAP Purge Solenoid, an open or shorted harness, or a poor electrical connection in the solenoid circuit.
To fix this issue, you should visually inspect the wiring harness and connectors for any damage. Look for broken, bent, pushed out, or corroded pins in the connectors.
The repair time for this issue is estimated to be around 1.0 hour. It is important to address this problem promptly to prevent further damage to the vehicle.
Repair Importance Level | 10.0 (Out of 10) |
Estimated Repair Time | Approximately 1.0 hour |
Repair Difficulty Level | 10.0 (Out of 10) |
Unveiling The Mystery: Symptoms Of Fault Code P1655 Revealed!
When the engine light is on or the service engine soon warning light is illuminated, it could be a sign of the p1655 fault code.
- The symptoms of the automobile fault code P1655 include the Engine Light being ON or the Service Engine Soon Warning Light being illuminated.
Unveiling The Culprits: Decoding The Causes Of Code P1655
The automobile fault code p1655 can be caused by a faulty EVAP Purge Solenoid, an open or shorted EVAP Purge Solenoid harness, or a poor electrical connection in the EVAP Purge Solenoid circuit.
- The fault code P1655 can be caused by the following: a faulty EVAP Purge Solenoid, an open or shorted EVAP Purge Solenoid harness, and a poor electrical connection in the EVAP Purge Solenoid circuit.
- Pinpoints your car-specific issues, giving accurate diagnostics for your exact make and model.
- Works anywhere, even with limited connectivity, making it highly versatile.
- Provides detailed insights into real-time performance for your exact make and model, beyond generic online explanations.
- Tracks past issues of your vehicle, helping you spot recurring problems and monitor long-term performance, which online resources can’t offer.
- Detects potential issues early, helping avoid costly repairs instead of just addressing current problems.
- Regular checks support efficiency and emissions standards, potentially increasing resale value—hard to gauge with online info alone.
Fixing Code P1655: Simple Steps To Resolve The Issue!
To fix the p1655 fault code, start by visually inspecting the wiring harness, connectors, and components for any damage or corrosion.
- To fix the automobile fault code P1655, follow these steps: 1.
- Check the possible causes mentioned above.
- 2.
- Visually inspect the wiring harness and connectors related to the fault code.
- 3.
- Look for any damaged components.
- 4.
- Check for broken, bent, pushed out, or corroded pins in the connectors.
- The estimated repair time for this fix is 1.0 hour.
Cracking The Code: P1655 Fixing Cost And Complexity Unveiled!
The factors influencing the diagnosis and fixing cost of the automobile fault code P1655 are the estimated repair time of 1.0 hour and the average hourly rate charged by auto repair shops, which ranges between $75 and $150.
P1655 Fault Code: Understanding The Description And Troubleshooting Steps
The P1655 fault code indicates that there is an issue with the control circuit of the EVAP purge solenoid. The Powertrain Control Module (PCM) has detected that the voltage level on the output driver module for the solenoid is not correct. This means that the PCM is not able to properly control the operation of the EVAP purge solenoid, which is responsible for regulating the flow of fuel vapor from the charcoal canister to the engine intake manifold.
When this fault code is triggered, it can result in various symptoms such as rough idling, decreased fuel efficiency, and even stalling of the engine.
It is important to address this issue promptly to prevent further damage to the vehicle and ensure optimal performance.
A qualified technician will need to diagnose the exact cause of the fault code and perform the necessary repairs or replacements to resolve the issue with the EVAP purge solenoid control circuit.
FAQ
If you see the engine light or service engine soon warning light on, the fault code P1655 could be the culprit. This code is often caused by a faulty EVAP purge solenoid, an open or shorted EVAP purge solenoid harness, or a poor electrical connection in the EVAP purge solenoid circuit. To fix this issue, visually inspect the wiring harness and connectors, checking for any damage or corrosion. Also, look out for broken, bent, pushed out, or corroded connector pins.
To fix the P1655 fault code, start by visually inspecting the wiring harness and connectors. Look for any damaged components and check if there are any broken, bent, pushed out, or corroded pins in the connectors. This can help identify if the issue lies with a faulty EVAP Purge Solenoid or if there is an open or shorted circuit in the harness. Don’t forget to check the “Possible Causes” listed above for further troubleshooting.
When resolving the P1655 fault code, start by checking for damaged components and connector’s pins. This can be done by visually inspecting the related wiring harness and connectors. Look for any signs of damage such as broken, bent, pushed out, or corroded pins. By doing this, you can identify any issues with the EVAP Purge Solenoid or its circuit connections. This will help you determine if the fault lies in a faulty solenoid, an open or shorted harness, or a poor electrical connection.
Wrap Up
If your engine light is on and you’re seeing the P1655 fault code, it could be due to a faulty EVAP Purge Solenoid or issues with the solenoid’s harness and electrical connection. To fix this, visually inspect the wiring harness and connectors, checking for any damage or corrosion. Look out for broken or bent pins on the connectors as well.