[SOLVED] P126F Code: Fixing Nitrogen Oxide Sensor Trailing Throttle Signal Too Rich

The automobile fault code P126F indicates a problem with the Nitrogen Oxide (NOx) Sensor. The most common symptom is the Engine Light being ON or the Service Engine Soon Warning Light.

The cause of this fault code can be a faulty NOx sensor, an open or shorted NOx sensor harness, or a poor electrical connection in the NOx sensor circuit. To fix this issue, you should visually inspect the wiring harness and connectors, checking for any damage or corrosion.

Additionally, look for any broken, bent, pushed out, or corroded pins in the connectors. The repair time for this issue is estimated to be around 1.0 hour.

It is important to address this fault code promptly to ensure optimal engine performance and emissions control.

Repair Importance Level10.0 (Out of 10)
Estimated Repair TimeApproximately 1.0 hour
Repair Difficulty Level10.0 (Out of 10)

When the engine light is on or the service engine soon warning light is illuminated, it could be a sign of the p126f fault code.

  • The symptoms of the automobile fault code p126f include the Engine Light being ON or the Service Engine Soon Warning Light being illuminated.

The automobile fault code p126f can be caused by a faulty NOx sensor, an open or shorted sensor harness, or a poor electrical connection in the sensor circuit.

  • The fault code p126f can be caused by a faulty Nitrogen Oxide (NOx) Sensor, an open or shorted Nitrogen Oxide (NOx) Sensor harness, or a poor electrical connection in the Nitrogen Oxide (NOx) Sensor circuit.

To fix the automobile fault code p126f, start by visually inspecting the wiring harness, connectors, and components for any damage or corrosion.

  • To fix the automobile fault code p126f, you need to follow these steps: 1.
  • Check the possible causes mentioned above.
  • 2.
  • Visually inspect the wiring harness and connectors related to the fault code.
  • 3.
  • Look for any damaged components.
  • 4.
  • Check for broken, bent, pushed out, or corroded pins in the connectors.
  • 5.
  • Repairing this fault code is estimated to take approximately 1.0 hour.

The automobile fault code p126f can be diagnosed and fixed within an estimated repair time of 1.0 hour. The cost of the repair will depend on the hourly rate charged by the auto repair shop, which typically ranges between $75 and $150 per hour.

The P126F fault code is related to the Nitrogen Oxide (NOx) Sensor in your vehicle. The Engine Control Module (ECM) constantly monitors this sensor to ensure it is functioning properly. When the NOx Sensor does not meet the factory specifications, the ECM sets the P126F code.

Specifically, the P126F code indicates that the Nitrogen Oxide Sensor Trailing Throttle Check Linear Lambda Signal is Too Rich.

This means that the sensor is detecting an excessive amount of fuel in the exhaust gases, resulting in a rich air-fuel mixture. When this fault code appears, it is important to address it promptly.

A rich air-fuel mixture can lead to increased emissions and reduced fuel efficiency.

It is recommended to have a qualified technician diagnose and repair the issue to ensure optimal performance and compliance with emissions regulations.

What are the possible causes for the automobile fault code p126f and how can I visually inspect them?

If you’re seeing the engine light on or the service engine soon warning light, the fault code P126F could be the culprit. This code is often caused by a faulty Nitrogen Oxide (NOx) sensor, an open or shorted NOx sensor harness, or a poor electrical connection in the NOx sensor circuit. To visually inspect these possible causes, check the wiring harness and connectors related to the NOx sensor. Look for any damaged components and examine the connector’s pins for any signs of being broken, bent, pushed out, or corroded.

How can I determine if the Nitrogen Oxide (NOx) Sensor harness is open or shorted in order to fix the p126f fault code?

If you’re dealing with the p126f fault code and your engine light is on, it’s likely due to a faulty Nitrogen Oxide (NOx) Sensor or an open or shorted NOx Sensor harness. To fix this issue, start by visually inspecting the wiring harness and connectors. Look for any signs of damage, such as broken or bent pins, corrosion, or components that are pushed out. This thorough check will help you identify and address any issues with the NOx Sensor harness.

What steps should I take to check for damaged components and inspect the wiring harness and connectors to resolve the p126f fault code?

To resolve the p126f fault code, start by visually inspecting the wiring harness and connectors. Look for any signs of damage, such as broken or bent pins, or corrosion. Check for any faulty components and ensure a secure electrical connection. This will help identify and resolve any issues with the Nitrogen Oxide (NOx) Sensor and its circuit.

p126f error fault code explained

If you’re seeing the Engine Light ON or the Service Engine Soon Warning Light, the p126f fault code might be the culprit.

This code is usually caused by a faulty Nitrogen Oxide (NOx) Sensor or issues with the sensor’s harness and circuit connection.

To fix it, visually inspect the wiring harness and connectors, checking for any damage or corrosion.

Look out for broken, bent, pushed out, or corroded connector pins.

Scroll to Top