[SOLVED] P11Ce Code: Low Voltage In Throttle/Pedal Position Sensor/Switch ‘d’ – How To Fix

The automobile fault code P11CE indicates a problem with the accelerator pedal. When this fault code appears, the engine light or service engine soon warning light will turn on. The possible causes of this issue include a faulty accelerator pedal, an open or shorted accelerator pedal harness, a poor electrical connection in the accelerator pedal circuit, or a faulty accelerator pedal module.

To fix this problem, you should visually inspect the wiring harness and connectors, checking for any damage or corrosion.

Additionally, look for any broken, bent, pushed out, or corroded pins in the connectors. The repair time for this issue is estimated to be around 1.0 hour. It is important to address this fault code promptly to ensure the proper functioning of your vehicle.

Repair Importance Level10.0 (Out of 10)
Estimated Repair TimeApproximately 1.0 hour
Repair Difficulty Level10.0 (Out of 10)

If you see the Engine Light ON or the Service Engine Soon Warning Light, it could be a sign of the p11ce fault code.

  • The symptoms of the automobile fault code p11ce include the Engine Light being ON or the Service Engine Soon Warning Light being illuminated.

The automobile fault code p11ce can be caused by a faulty accelerator pedal, open or shorted accelerator pedal harness, poor electrical connection in the accelerator pedal circuit, or a faulty accelerator pedal module.

  • The fault code P11CE can be caused by a faulty accelerator pedal, an open or shorted accelerator pedal harness, a poor electrical connection in the accelerator pedal circuit, or a faulty accelerator pedal module.

To fix the p11ce fault code, start by visually inspecting the wiring harness, connectors, and components for any damage or corrosion.

  • To fix the automobile fault code p11ce, you need to follow these steps: 1.
  • Check the possible causes mentioned above.
  • 2.
  • Visually inspect the wiring harness and connectors related to the fault code.
  • 3.
  • Look for any damaged components.
  • 4.
  • Check for broken, bent, pushed out, or corroded pins in the connectors.
  • 5.
  • Repairing this fault code is estimated to take approximately 1.0 hour.

The factors influencing the diagnosis and fixing cost of the automobile fault code p11ce are the estimated repair time and the hourly rate charged by auto repair shops. The estimated repair time for this fault code is 1.0 hour. Auto repair shops typically charge between $75 and $150 per hour for their services.

These factors will determine the overall cost of diagnosing and fixing the p11ce fault code.

The fault code P11CE indicates a problem with the ThrottlePedal Position SensorSwitch ‘D’ Circuit Voltage being too low.

This fault code is related to the accelerator pedal position and is monitored by two individual sensors for redundancy and malfunction recognition.

The sensors register the pedal travel as angular deflection and transmit the data as analog linear voltage curves to the engine-management control unit.

The overall pedal travel is mechanically expressed as 16° ±0.5°.

The engine-management control unit compares the input signals from the sensors for plausibility, considering factors such as mutual synchronicity and linearity.

In the case of the P11CE fault code, the voltage at pedal sensor 1 is detected to be lower than the lower limit value of 0.51 V.

What are the possible causes of the automobile fault code P11CE?

If you see the engine light or service engine soon warning light on, the fault code P11CE could be the culprit. This code is often caused by a faulty accelerator pedal or issues with the accelerator pedal circuit. To fix it, start by visually inspecting the wiring harness and connectors. Look for any damage or corrosion on the components and check if any connector pins are broken, bent, pushed out, or corroded. Don’t forget to check the possible causes mentioned above to ensure a thorough diagnosis.

How can I visually inspect the wiring harness and connectors to fix the P11CE fault code?

To fix the P11CE fault code, start by visually inspecting the wiring harness and connectors. Look for any damaged components and check if there are any broken, bent, pushed out, or corroded pins in the connectors. This can help identify any issues with the accelerator pedal or its circuit. Don’t forget to check the other possible causes mentioned, such as a faulty accelerator pedal module.

What should I look for when checking for damaged components and connector pins to resolve the P11CE fault code?

When resolving the P11CE fault code, start by checking for damaged components and connector pins. This can be done by visually inspecting the related wiring harness and connectors. Look for any signs of damage such as broken, bent, pushed out, or corroded connector pins. By doing this, you can identify any issues that may be causing the fault code and take the necessary steps to fix them.

p11ce error fault code explained

If you’re seeing the Engine Light ON or the Service Engine Soon Warning Light, it could be due to a faulty Accelerator Pedal or issues with the wiring harness and connectors. To fix it, visually inspect the wiring and connectors, check for damaged components, and look for any broken, bent, pushed out, or corroded pins on the connectors.

Scroll to Top