The OBD code P220E for Ford indicates an issue with the NOx sensor system.
Symptoms include the Engine Light being ON.
Common causes are a faulty NOx sensor, open or shorted NOx sensor harness, poor electrical connection in the NOx sensor circuit, or a faulty Engine Control Module (ECM).
This is a moderate issue.
To fix, inspect the wiring harness and connectors for damage or corrosion, and check connector pins for any issues.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
Symptoms of the Ford p220e OBD Code
The vehicle may experience issues related to the exhaust gas temperature sensor circuit.
- Symptoms: Engine Light ON.
- Reduced engine power.
- Loss of acceleration.
- Rough idle.
- Engine stalling.
- Turbocharger underboost condition.
Causes of the Ford p220e OBD Code
Do you know you can clear most fault codes—but some could mean serious danger? Don’t take chances with your safety or your family’s safety. This budget-friendly car scanner makes it easy to clear fault codes in seconds while showing you exactly what’s wrong. Plug it in, connect to your Android or iOS phone, and instantly check live data. You’ll know if it’s a minor issue you can clear or something serious that needs attention—so you can drive safely and stress-free. (Today’s Deal)
P220E in Ford vehicles typically indicates an issue with the NOx sensor circuit.
- P220E can be caused by a faulty NOx Sensor.
- A NOx Sensor harness that is open or shorted.
- A NOx Sensor circuit with poor electrical connection.
- Or a faulty Engine Control Module (ECM).
Fixing Ford Error Code p220e Step By Step
Address the issue by inspecting the NOx sensor circuit for potential faults or wiring problems.
- To fix the Ford OBDII code P220E, start by reviewing the possible causes mentioned above.
- Visually examine the corresponding wiring harness and connectors for any damage.
- Inspect the connector pins for signs of being broken, bent, pushed out, or corroded.
- Check the operation of the NOx sensor and its wiring for any faults.
- Replace the NOx sensor if necessary.
- Clear the fault codes and perform a test drive to verify the repair.
- If the code returns, further diagnostics may be needed to pinpoint the exact cause.
Cost Of Fixing Ford p220e Fault Code
Diagnosing and repairing fault code P220E on a Ford typically involves addressing the NOx sensor circuit.
The cost to diagnose and fix the Ford OBD code P220E typically ranges from $75 to $150, with an estimated repair time of 1. 0 hour.
Costs may vary based on shop rates, complexity of the issue, and any additional parts or labor needed for the repair.
That fault code is a turning point. If repair costs are climbing and your current loan feels like it’s holding you back, this is the time to plan ahead. The free Car Loan Payment Tracker helps you see how quickly you can pay off what’s left—and start preparing, with confidence, for your dream car.
Details of the Ford p220e OBD Code
P220E code indicates an issue with the NOx sensor circuit in a Ford vehicle.
Ford OBD code P220E means that the NOx sensor circuit range/performance problem has been detected.
This code is triggered by the Engine Control Module (ECM) when it detects that the signal from the NOx sensor is out of the expected range or not performing as it should.
The NOx sensor is part of the vehicle’s emissions control system and is responsible for monitoring the levels of nitrogen oxide in the exhaust gases.
When the NOx sensor malfunctions or sends incorrect signals, it can trigger code P220E.
Mechanic’s Tech Notes
Detailed information on Ford code P220E, including possible causes and diagnostic procedures.
To diagnose and fix OBDII code P220E in a Ford vehicle, start by visually inspecting the wiring harness and connectors related to the Transmission Control Module (TCM).
Look for any damage or corrosion on the connector pins.
Use a multimeter to check TCM power and ground connections.
Utilize a scan tool to confirm TCM communication over the Controller Area Network (CAN) network.
If necessary, consider reprogramming or reflashing the TCM.
This process can help identify and address issues related to the TCM that may be triggering the P220E fault code.
FAQ
Common symptoms of OBD code P220E in a Ford vehicle include Engine Light ON, caused by issues like faulty NOx sensor or ECM. Inspect wiring and connectors for damage.
Typical cause of Ford OBD code P220E is a faulty NOx sensor, open/shorted harness, poor connection, or faulty ECM. Inspect wiring and connectors for damage.
Diagnose P220E by checking NOx sensor, harness, and ECM. Inspect wiring for damage or corrosion. Repair as needed to resolve the issue.
Wrap Up
If your Ford is displaying OBD code p220e and experiencing issues with the reductant injector control circuit, it could be caused by a faulty reductant injector, damaged wiring harness, poor electrical connection, or a defective powertrain control module (PCM).
To address Ford OBD code p220e, start by inspecting the reductant injector and its wiring for any visible damage.
Test the electrical connectors for proper connection and corrosion.
Consider replacing the reductant injector if necessary and ensure the wiring harness is securely connected.
If the issue persists, further diagnostics may be needed to check
